Pyle-audio PP5600 Manual do Utilizador

Rev.: A PP5600 SERIES POS PRINTER USER’S MANUAL Never attempt to repair this product yourself. Improper repair work can be dangerous. Do

1 - 6G. MAIN PARTS ON THE EXTERIOR Parallel Connector Serial Connector Power Connector Peripheral Connector Frame Ground Rear View Sc

1 - 7 Indicators • Power LED: green • Error LED: red • Paper Out LED: red Interior View Auto Cutter Ribbon Cassette Area Paper Guide Roller Pa

2 - 1 II. QUICK START-UP A. CONNECTING CABLES 1. Serial connection All the external connectors are in the recessed area at the rear bottom. The

2 - 2split cable 20867023800 (CCBLA-238) is used instead, this port can control two cash drawers of above models. When the printer is used as a kitc

2 - 3 B. LOADING / REPLACING RIBBON CASSETTE • Turn off the power to the printer. • Lift the front end of the top cover to remove it. • Open the aut

2 - 4• Turn the knob counterclockwise to remove slack in ribbon for use. • Apply even force to close the auto cutter (PP5600B) so that the small lug

2 - 5 paper feed roller inside the print mechanism then the paper will automatically advance to proper position (paper exit of print mechanism). In

2 - 6bottom of the slip is an indicator for adjustment on so-called bi-directional printing offset. E. SPECIAL ADJUSTMENTS 1. Paper near en

2 - 7 position switch at the left is coded S2 for general printer settings. a.Bi-directional printing offset - S1 Pos. 1 Off On Off On Off On Off On

P/N: 19380900020 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the

2 - 8Positions 1 to 6 of the S2 switch define the communication protocol and handshaking criteria in RS232 interface. They shall always be set to po

3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES B. GENERAL CLEANING Please use a soft hair brush or compressed air to clear awa

3 - 22. Printing Problems Nothing can be printed with ERROR LED ON – Check the Paper Out LED. If it is ON, most probably the paper roll is not inst

3 - 3 3. Paper Jam Problems Paper is jammed inside the printer – Please follow procedures below. • Turn off the printer. • Open the top cover a

3 - 4 To check for home position of the auto cutter, please open the auto cutter and look into the blade slot and the spindle hole as in picture

4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Dot matrix impact method Print head configuration 9 pins Printing directi

4 - 2C. RIBBON CASSETTE ITEM REQUIREMENT RECOMMENDED TYPE RC200P COLOR Purple RIBBON MATERIAL Nylon 66 RIBBON WIDTH 13 mm CASSETTE DIMENSION 14

i Table Of Contents BEFORE STARTED . . . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . .

ii Printing problems . . . . . . . . . . . . . . . . . . . . .3 -- 2 Paper jam problems . . . . . . . . . . . . . . . . . . . 3 -- 3 Auto cutte

1 - 1 I. BEFORE STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading; high performance; high reliability 9 p

1 - 2It even supports some enhancement capability for reminder function to persons around. It can be used to drive a separately purchased kitchen b

1 - 3 • Supports Posiflex kitchen bell drive when used as kitchen printer • Hardware hand shaking in serial interface through DIP switch selection

1 - 4Length of the interface cable depends on whether the order includes the power adaptor. When power adaptor is included, the interface cable is 6

1 - 5 F. IMPORTANT TIPS Never attempt to disassemble or modify this product. Unauthorized interior access voids product warrant